3 Ways to Connect Coaxial Cable Connectors - wikiHow (2024)

  • Categories
  • Computers and Electronics
  • Television
  • Connecting Devices to Television Sets

Download Article

Explore this Article

methods

1Choosing and Stripping Cables

2Attaching a Crimp Connector

3Installing a Right-Angle Connector

Other Sections

Tips and Warnings

Things You'll Need

Related Articles

References

Co-authored byMantas Silvanavicius

Last Updated: April 14, 2023Fact Checked

Download Article

A coaxial cable (coax) brings TV and internet signals into homes and other buildings. These cables need connectors on the end to hook up to appliances like TVs and transmit signal. If you have a coax cable without a connector, installing your own is a simple task. Strip the wire and expose its inner conductor. Then push a connector over it and crimp it in place. For tight spaces, use a right-angle connector to avoid bending the cable too much.

Method 1

Method 1 of 3:

Choosing and Stripping Cables

Download Article

  1. 1

    Determine whether you have an RG59 or RG6 cable. These are the 2 most common types of coax cables, and you probably have one or the other. The easiest way to tell is to look at the rubber housing of the cable. The type should be printed here.[1]

    • The main difference between the cables is that RG6 is thicker and has more padding than RG59. This makes it more durable, and a more common choice for cable and internet wiring.
  2. 2

    Get a connector that matches your cable type. The most common coax connector is F type. Find an F type connector at a hardware store and match it to your cable width. Get one for each cable you’re connecting.[2]

    • There are also N type connectors, though these are much less common in home installations.
    • F type connectors still come in a variety of styles, including crimp and twist on. Speak to a store employee if you don’t know which option is best for you.

    Advertisement

  3. 3

    Cut through the rubber 12 inch (1.3cm) from the end of the cable. Use either a wire stripping tool or a razor. Measure 12 inch (1.3cm) from the end of the cable and cut around the outer rubber layer. Then pull it off to expose the mesh underneath.[3]

    • Don’t cut all the way through the cable. Just cut the outer rubber covering. Cutting too deep will damage the connection.
    • If you use a razor to do this, be very careful. Don’t put your finger in the path of the blade and hold the cable tightly.
  4. 4

    Peel the wire mesh down. This wire mesh is the second layer of the cable. Use your fingers or a pair of pliers and peel the mesh back. Fold it down over the rubber housing below the first cut you made.[4]

    • A wire stripping tool could cut through this section and remove it, but be careful if you do this. Don’t cut deep enough to damage the conductor in the center of the cable.
  5. 5

    Trim the dielectric plastic 14 inch (0.64cm) from the end of the cable. The final layer of insulation for the cable is a white plastic housing around the main conductor. Use a wire stripper or razor and gently cut around the plastic 14 inch (0.64cm) from the top. Then peel it away to expose the copper conductor underneath.[5]

    • The plastic may be foil-covered.
    • Be especially careful when removing the plastic covering. If you damage the conductor, your signal will be weaker.
  6. 6

    Remove any pieces of wire mesh touching the conductor. If any part of the mesh touches the conductor, it interferes with the signal quality. This is called a stinger. Double check that the entire wire mesh is peeled back, and no parts touch the conductor.[6]

  7. Advertisement

Method 2

Method 2 of 3:

Attaching a Crimp Connector

Download Article

  1. 1

    Slide the crimp ring over the cable. Leave it below the spot where you cut so it’s out of the way until you need it. Make sure you slide the ring on first, or you’ll have to remove the connector later on and start over.[7]

    • Not all connectors have separate crimp rings. Some connectors have the crimp ring already attached. Check which type you have.
  2. 2

    Push the connector over the cable so the copper conductor sticks out. Hold the cable in one hand and the connector in the other. Then insert the conductor into the hold in the center of the connector. Continue pushing until the conductor sticks out just above the edge of the connector on the other side.[8]

    • This will take some pushing because the connector have to wedge in between the rubber housing and plastic layer. Try twisting the connector back and forth a little to work it onto the cable.
    • If you’re installing the cable outdoors, remember to use a waterproof connector. This is housed with rubber.
  3. 3

    Crimp the connector and wire. A crimping tool pushes the crimp ring completely inside the connector, securing the connection. Select the correct die, or width, for the cable you’re using. Then insert the cable into the crimping tool. Squeeze the handle until you hear a click, indicating that the crimp is complete.[9]

    • Some crimping tools work differently. Follow the directions on the specific tool you use.
  4. 4

    Trim away any wire mesh coming out from under the connector. These metal pieces could interfere with your signal or wiring. Check around the connector for any wires coming out. If you see any, use a wire cutter and trim them away.[10]

    • No bare wire should be showing.
  5. Advertisement

Method 3

Method 3 of 3:

Installing a Right-Angle Connector

Download Article

  1. 1

    Place the connector base over the wire. Most right-angle connectors have a base piece that holds the housing together. Slide this base over the stripped wire so it’s there after you install the connector.[11]

    • Remember to slide the base on first, before installing any other pieces of the connector. If you forget, you’ll have to remove the connector and redo the process.
    • Some right-angle connector kits are different. Follow the procedure on whichever product you use.
  2. 2

    Loosen the screw inside the connector. The front portion of the connector housing has an internal screw that carries the signal. Turn the screw counterclockwise to loosen it.[12]

    • Don’t remove the screw completely. Just loosen it.
  3. 3

    Touch the conductor to the screw and tighten it. Insert the cable into the housing so the conductor touches the screw. Hold it in place and turn the screw clockwise to tighten it. Form a snug connection so the cable stays in place.[13]

    • Only tighten until the screw is snug. Don’t overtighten it or you could damage the copper conductor.
  4. 4

    Install the back housing of the connector. Take the back portion and line it up with the notches on the front. Then press the 2 pieces together with the cable in between them.[14]

    • Some connectors may click together at this point. Continue holding the pieces together just in case they don’t automatically attach.
  5. 5

    Twist the connector base around the connector. The base locks the two sections together. Push it up until it reaches the connector, then twist it over the two pieces. Make sure the connection is snug, then the job is complete.[15]

  6. 6

    Finished.

  7. Advertisement

Community Q&A

Search

Add New Question

  • Question

    Can I connect sky cable to a digital aerial?

    3 Ways to Connect Coaxial Cable Connectors - wikiHow (22)

    Community Answer

    Yes, but the thin twin cable probably isn't as good as even a normal TV cable. Still, it's likely to work well enough, unless your signals are exceptionally poor.

    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHow

    YesNo

    Not Helpful 9Helpful 14

  • Question

    Will my router need to be hooked up to one to connect to the internet?

    3 Ways to Connect Coaxial Cable Connectors - wikiHow (23)

    Community Answer

    Although the thin twin cable probably isn't as good as even normal TV cable, it's likely to work well enough, unless your signals are exceptionally poor.

    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHow

    YesNo

    Not Helpful 8Helpful 9

  • Question

    Will connecting more connectors affect the quality of the signals?

    3 Ways to Connect Coaxial Cable Connectors - wikiHow (24)

    Community Answer

    Yes, negatively, though seldom significantly. It's always better to use a cable of the correct length than to join shorter ones together.

    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support wikiHow

    YesNo

    Not Helpful 3Helpful 6

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

      Advertisement

      Tips

      • If you have high speed internet and more than two TV's, make sure you use a high quality RG 6-type connector.

        Thanks

        Helpful6Not Helpful1

      • Screw-on style F connectors usually provide a weaker connection, and signal can bleed out of the cable. Crimp-style connectors are better for a strong signal.

        Thanks

        Helpful3Not Helpful1

      Submit a Tip

      All tip submissions are carefully reviewed before being published

      Name

      Please provide your name and last initial

      Submit

      Thanks for submitting a tip for review!

      Advertisement

      Things You'll Need

      • Coaxial cable
      • Coaxial connector
      • Wire cutters
      • Cable strippers
      • Pliers
      • Razor
      • Crimper
      • Wire strippers

      You Might Also Like

      How toTerminate Coaxial CableHow toMake a TV Antenna with a Potato
      How toWall Mount a Plasma TVHow toConnect PC to TV4 Easy Ways to Connect an iPhone or Android to a TVHow to Connect your Samsung TV to the Internet: Quickstart GuideHow to Connect Your PC to an LG Smart TV: 3 Easy MethodsConnect a Fire Stick to Wi-Fi With or Without a RemoteHow toHook Up a VCR to a TV4 Steps to Connect a DVD Player to a Samsung TVHow to Connect Any Phone to Your TV via USBHow to Set Up Your Roku Player and Connect it to a TVA Guide to Connecting a DVD Player to an LG Smart TVHow toHook Up a Laptop to a TV

      Advertisement

      More References (6)

      About This Article

      MS

      Co-authored by:

      Mantas Silvanavicius

      Licensed Electrician

      This article was co-authored by Mantas Silvanavicius. Mantas Silvanavicius is a Licensed Electrician and the Owner of M+S Electric based in Las Vegas, Nevada. With more than 20 years of experience, he specializes in home electrical installations, testing, and wiring. Mantas and his team have completed projects for companies such as Seiko and Springhill Suites by Marriott. M+S Electric is licensed, bonded, and insured. This article has been viewed 2,066,659 times.

      How helpful is this?

      Co-authors: 35

      Updated: April 14, 2023

      Views:2,066,659

      Categories: Connecting Devices to Television Sets

      In other languages

      French

      Spanish

      German

      Portuguese

      Chinese

      Russian

      Indonesian

      • Print
      • Send fan mail to authors

      Thanks to all authors for creating a page that has been read 2,066,659 times.

      Reader Success Stories

      • 3 Ways to Connect Coaxial Cable Connectors - wikiHow (40)

        Tora Stone

        May 19, 2017

        "This was wonderful help. From start to finish it enabled me, a woman in her 70's, to change the whole set of..." more

      More reader storiesHide reader stories

      Is this article up to date?

      Advertisement

      3 Ways to Connect Coaxial Cable Connectors - wikiHow (2024)

      References

      Top Articles
      Latest Posts
      Recommended Articles
      Article information

      Author: Patricia Veum II

      Last Updated:

      Views: 5996

      Rating: 4.3 / 5 (64 voted)

      Reviews: 87% of readers found this page helpful

      Author information

      Name: Patricia Veum II

      Birthday: 1994-12-16

      Address: 2064 Little Summit, Goldieton, MS 97651-0862

      Phone: +6873952696715

      Job: Principal Officer

      Hobby: Rafting, Cabaret, Candle making, Jigsaw puzzles, Inline skating, Magic, Graffiti

      Introduction: My name is Patricia Veum II, I am a vast, combative, smiling, famous, inexpensive, zealous, sparkling person who loves writing and wants to share my knowledge and understanding with you.